Products
Standard A-Frame Aquarium Bouncy Castle
  • Standard A-Frame Aquarium Bouncy CastleStandard A-Frame Aquarium Bouncy Castle
  • Standard A-Frame Aquarium Bouncy CastleStandard A-Frame Aquarium Bouncy Castle
  • Standard A-Frame Aquarium Bouncy CastleStandard A-Frame Aquarium Bouncy Castle
  • Standard A-Frame Aquarium Bouncy CastleStandard A-Frame Aquarium Bouncy Castle

Standard A-Frame Aquarium Bouncy Castle

Leisure Activities® offers the Standard A-Frame Aquarium Bouncy Castle for commercial sourcing, featuring a pitched-roof structure designed around an ocean-themed play environment. Its 5.5 × 4.0 m footprint, 3.4 m roof ridge and three-sided mesh windows distinguish it from conventional flat-top bounce castles.

Leisure Activities® Standard A-Frame Aquarium Bouncy Castle is available for wholesale orders and custom printing. Its two-panel pitched roof directs rain towards the sides, while the printed underside carries the ocean theme into the bouncing area. Netted windows on three sides provide visibility into the play chamber.

Standard A-Frame Aquarium Bouncy Castle
01

Features

The unit is a single-chamber castle with a pitched roof, netted windows on three sides and an ocean print that runs from the entrance across the interior walls. The entrance is wide enough for an adult to step in after a toddler.

The shell is 5.5 x 4.0 m on the floor and 3.4 m at the ridge, and it weighs 109 kg. A 1.0 HP blower holds the shell at pressure, and the base carries webbing loops at the corners and mid-span.

Item Specification
Inflated size (L x W x H) 5.5 x 4.0 x 3.4 m / 18 x 13 x 11 ft
Unit weight 109 kg / 240 lb
Packed size 122 x 93 x 80 cm / 48 x 37 x 31 in
Outer material 17 oz Plato PVC tarpaulin, NFPA 701-2
Internal material 9 oz PVC, 8P phthalate-free
Roof Pitched A-frame, printed underside
Windows Netted panels on three sides
Blower 1.0 HP constant air, voltage to order
Anchor points Webbing loops, corners and mid-span
Assembly crew Two people, about 25 minutes
Packed with Blower, stakes, repair kit, manual
Optional Sandbag set, spare roof skin, sponsor panel
MOQ / lead time 1 piece / 30 days standard
Warranty 1 year limited on seams, blower 1 year
02

Roof Design

On the Standard A-Frame Aquarium Bouncy Castle the ridge seam is the highest loaded seam on the shell. It is double stitched, reinforced at both ends, and checked at every set-up because it takes the most sun and flexing.

Water runs off the two roof planes and away from the entrance. A level site matters more on this unit than on a flat-top castle, because a low corner holds water at the base skirt.

Element Build Check point
Roof Pitched A-frame, printed underside Ridge seam and drainage
Windows Small-mesh netting, three sides Tension and stitching
Entrance Stepped opening, adult height Entry lip and reinforcement
Walls Printed PVC panels Print alignment at seams
Base Webbing loops, corners and mid-span Loop stitching
03

Applications

The Standard A-Frame Aquarium Bouncy Castle suits aquariums, garden centres, museums and shopping centres running a marine exhibition or a summer campaign. The pitched roof gives the shell a building silhouette rather than a toy profile.

The unit fits a courtyard, an atrium or a forecourt where a domed castle would look out of place, and the netted windows let parents watch from outside.

Standard A-Frame Aquarium Bouncy Castle
04

Installation

Two people inflate the unit in about 25 minutes. On grass, stake every corner and mid-span loop; on paving, decking or artificial grass, use sandbags or water ballast, because stakes damage the surface.

The roof catches wind on both planes, so the windward side carries extra ballast and the unit comes down when gusts pick up. Indoors, measure to the lowest beam or light fitting.

Standard A-Frame Aquarium Bouncy Castle
05

Customization

Print covers the walls, roof and entrance. A sponsor logo sits on the entrance panel, which is the surface most often photographed, and a venue logo sits on the side wall.

Proofing runs on a printed panel checked in daylight before production, and a licensed character needs written permission with the file.

06

Packing & Inspection

At 109 kg the unit is a two-person lift. The roof section is folded on top of the roll so the ridge seam is not compressed, and the blower travels in its own carton.

The packed case is 122 x 93 x 80 cm. Each unit is inflated and checked at the seams before packing, and a written inspection record is available on request.

Get A Quote Now — send the theme, the voltage and the site surface, and we reply with the quotation and panel options.

PackingPackingPackingPacking

07

Attraction Buyer Questions

Q: Does the roof of the Standard A-Frame Aquarium Bouncy Castle hold water in rain?

A: No. The two planes meet at a ridge and drain down the slope, and the entrance sits below the roof edge.

Q: Do we need stakes or sandbags?

A: Stakes on grass; sandbags or water ballast on paving, decking and artificial grass. The base loops take either.

Q: Can the print match our exhibition branding?

A: Yes. Vector artwork and Pantone references are proved on a printed panel before production.

Q: Is a spare roof skin available?

A: Yes. The roof is a replaceable section on this model and is quoted against the serial number.

Q: Which voltage does the blower use?

A: Order 220-240 V / 50 Hz or 110 V / 60 Hz; the plug is matched to the site supply.

Send Inquiry
Contact Info
Send us your detailed inquiry about Inflatable Bouncy Castles,Inflatable Sports Games,Inflatables Accessories, wholesale orders, customized projects or OEM requirements. Our professional team will reply with quotation and solution quickly.
X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
RejectAccept