Products
Small T-Rex Multiplay Bounce Castle
  • Small T-Rex Multiplay Bounce CastleSmall T-Rex Multiplay Bounce Castle
  • Small T-Rex Multiplay Bounce CastleSmall T-Rex Multiplay Bounce Castle
  • Small T-Rex Multiplay Bounce CastleSmall T-Rex Multiplay Bounce Castle
  • Small T-Rex Multiplay Bounce CastleSmall T-Rex Multiplay Bounce Castle
  • Small T-Rex Multiplay Bounce CastleSmall T-Rex Multiplay Bounce Castle

Small T-Rex Multiplay Bounce Castle

Leisure Activities® Small T-Rex Multiplay Bounce Castle is a compact inflatable multiplay bouncy castle combining a bounce bed, climbing section, and slide within a 5.8m x 3.2m x 2.9m (19ft x 11ft x 10ft) footprint. Weighing 113 kg (251 lbs) and built from 17oz PVC vinyl, it is engineered for birthday rentals, indoor play centers, school events, and venues with restricted floor space or ceiling clearance.

The Small T-Rex Multiplay Bounce Castle is configured specifically for mobile hire operators needing multi-activity engagement where installation area is constrained. The structure pairs an internal jumping floor with a climbing ramp leading to a 1.3m (51-inch) high-speed exit slide, establishing a continuous, one-way player flow that reduces congestion at the entrance.

Visually anchored by an integrated 3D T-Rex arch and dinosaur-themed interior wall artwork, the unit provides high visual recognition for event environments without expanding its transport or packed profile.

Small Inflatable Multiplay T-REX Bouncy Castle with Slide
01

Structural Safety

17oz PVC Vinyl Shell: Constructed using 17oz commercial PVC vinyl selected for tensile strength, tear resistance, and surface cleanability under frequent rental turnover.

Reinforced Seam Architecture: High-stress load points, slide bed terminations, and internal wall baffles utilize double-thread lock-stitching to accommodate dynamic user pressure.

1.3m Platform Enclosure: The elevated 1.3m slide platform is fitted with high-density vertical safety mesh and side walls to enforce a seated posture before descent.

Base Anchoring Hardware: Heavy-duty steel D-rings stitched into structural webbing are positioned along the base perimeter to allow mechanical anchoring via ground stakes or sandbags.

02

Compliance Evidence

EN 14960-1:2019 Standard: Small T-Rex Multiplay Bounce Castle manufactured in accordance with EN 14960-1:2019 safety requirements for inflatable play equipment. Product-specific SCT Certificates and RPII Inspector Reports are available upon request for venue licensing.

Material Flame Retardancy: The 17oz PVC fabric conforms to NFPA 701-2 test methods for flame propagation resistance.

Chemical Safety: Fabric formulations pass 8P Phthalate chemical testing for children’s contact equipment.

Factory Management Systems: Manufactured in facilities operating under ISO 9001 (Quality Management), ISO 14001 (Environmental Management), and ISO 45001 (Occupational Health & Safety) frameworks.

ISO 9001
ISO 9001
ISO 14001
ISO 14001
ISO 45001
ISO 45001
Verification of Conformity
Verification of Conformity
RPII Inspector
RPII Inspector
NFPA 701 Test Report
NFPA 701 Test Report
Phthalates 8P Test Report
Phthalates 8P Test Report
03

Technical Specifications

Parameter Operational Specification
Model Number CE003
Brand / Manufacturer Leisure Activities®
Inflated Dimensions (L x W x H) 5.8m x 3.2m x 2.9m / 19ft x 11ft x 10ft
Slide Platform Height 1.3m / 51 inches
Total Unit Weight 113 kg / 251 lbs
Packed Transport Volume 123cm x 84cm x 82cm / 48” x 33” x 32”
Primary Material Commercial 17oz PVC vinyl
Material Testing Compliance NFPA 701-2 test standard pass; 8P Phthalate-free chemical test pass
Air Inflation System 1 x 1.0 HP – 1.5 HP continuous electric air blower
Minimum Order Quantity (MOQ) 1 Piece
Production Lead Time 20 – 30 Days
Commercial Terms Bank Wire (T/T), 50% deposit before production, 50% balance before dispatch
04

Operational Safety Boundaries

To maintain safe operation during outdoor or indoor deployment, supervisors must enforce the following technical limits:

Maximum Operating Wind Speed: 24 mph (38 km/h / Beaufort Force 5). Discontinue operation, clear participants, and deflate the unit immediately if local wind gusts exceed this threshold.

Environmental Operating Limits: Do not set up or operate the equipment during heavy rain, lightning activity, or on uneven terrain containing sharp objects. Always deploy a heavy-duty ground tarp underneath the chassis.

Pre-Use Inspection Checklist:

Inspect the PVC surface, entry arch, and slide bed for tears, cuts, or seam separation.

Verify all base steel D-rings, anchor webbing straps, and ground stakes/ballasts are firmly attached.

Check the air blower intake grill for blockages and ensure the inflation sleeve cinch strap is tightly secured.

Small T-Rex Multiplay Bounce Castle Small T-Rex Multiplay Bounce Castle Small T-Rex Multiplay Bounce Castle Small T-Rex Multiplay Bounce Castle Small T-Rex Multiplay Bounce Castle Small T-Rex Multiplay Bounce Castle Small T-Rex Multiplay Bounce Castle Small T-Rex Multiplay Bounce Castle Small T-Rex Multiplay Bounce Castle

05

Quality Control & Manufacturing Process

Production of Model CE003 follows a structured, multi-stage Quality Assurance (QA) protocol managed by an independent team of 5+ QA inspectors reporting to factory management:

Raw Material Reception: Verification of incoming 17oz PVC vinyl rolls against thickness, weight, flame retardancy, and chemical specification sheets prior to release to production.

Cutting & Sewing Inspection: Automated pattern cutting verification and continuous roving inspections along peripheral sewing lines to confirm seam density and thread lock tension.

In-Process Assembly Checks: Inspections across gluing, hot-air welding, digital artwork printing, and seam reinforcement stages.

Inflation Holding Test: Completed units undergo continuous pressure testing and dimensional checks prior to cleaning and container packing.

workshopworkshopworkshop

06

Field Deployment, Storage & Maintenance

Single-Operator Handling: With a packed transport size of 123cm x 84cm x 82cm and weight of 113 kg, the unit can be maneuvered onto light utility vehicles and positioned using a standard hand truck.

Inflation Procedure: Attach the intake sleeve to a 1.0 HP – 1.5 HP blower, seal all quick-deflation zippers, and engage power. Inflation achieves operational pressure in under 10 minutes.

Cleaning & Field Repairs: Clean the PVC surface using warm water and a neutral soap solution. Each unit includes a repair patch kit and instruction sheet allowing venue staff to service minor surface abrasions following provided operational guidelines.

07

Ordering, OEM Capabilities & Intellectual Property

Supply Terms: Minimum order quantity is 1 piece with a standard 20 to 30-day production schedule. Shipments are supported by sales and warehouse logistics in Saint Petersburg, Florida (Americas) and China (Global).

OEM Customization: Custom color combinations, alternative dimensions, and facility branding prints can be integrated into the manufacturing process upon request.

IP Protection: Leisure Activities® manufactures under recognized industry technologies (including U.S. Patent 6,875,119) and respects client intellectual property rights, ensuring proprietary custom designs are not reproduced without authorization.

FactoryFactoryFactory

Send Inquiry
Contact Info
Send us your detailed inquiry about Inflatable Bouncy Castles,Inflatable Sports Games,Inflatables Accessories, wholesale orders, customized projects or OEM requirements. Our professional team will reply with quotation and solution quickly.
X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
RejectAccept