A Standard Dragon Multiplay Bounce Castle with a bounce chamber, a climb face and a single-lane slide off a 1.3 m deck. The shell weighs 167 kg and packs into a 135 x 95 x 78 cm case. The 17 oz shell is flame retardant to NFPA 701-2, the slide and platform are replaceable sections, and a 1.0-1.5 HP blower holds the tower and bed at pressure.
Standard Dragon Multiplay Bounce Castle from Leisure Activities®, a China manufacturer, is built around a 4.9 m tower. The tower carries the dragon head and the 1.3 m platform; the climb face runs up one side, and the slide drops from the platform into its own exit lane. The 5.2 x 5.5 m floor gives the bounce chamber the rest of the footprint.
01
Play Features
The unit combines three play elements in one shell: a bounce chamber, a climb face with moulded steps, and a single-lane slide off the platform. The 4.9 m roofline makes the tower the visual centre of the unit.
Entry and slide exit sit on different sides, so the queue at the steps does not meet riders landing at the bottom. The tower and the bed are inflated by one blower through a single tube.
Item
Specification
Inflated size (L x W x H)
5.2 x 5.5 x 4.9 m / 17 x 18 x 16 ft
Unit weight
167 kg / 368 lb
Packed size
135 x 95 x 78 cm / 53 x 37 x 31 in
Outer material
17 oz PVC tarpaulin, NFPA 701-2
Internal material
9 oz PVC, 8P phthalate-free
Play elements
Bounce chamber, climb face, single-lane slide
Platform height
1.3 m / 51 in
Tower height
4.9 m / 16 ft
Blower
1.0-1.5 HP constant air, voltage to order
Anchor points
Webbing loops, corners and mid-span
Assembly crew
Two to three people, about 25 minutes
Packed with
Blower, stakes, repair kit, manual
Optional
Spare slide panel, sandbag set, printed banner
MOQ / lead time
1 piece / 30 days standard
Warranty
1 year limited on seams, blower 1 year
02
Tower and Slide Design
On the Standard Dragon Multiplay Bounce Castle the slide is a separate chamber joined to the tower at a reinforced seam, so a slide repair does not flatten the tower. The platform deck is a stitched panel that can be replaced without opening the roof.
The climb face carries moulded steps and a grab line at the top. The slide exit has a double lip with replaceable edging, because that is where riders land and where the print wears first.
Element
Function
Check point
Bounce chamber
Play area at floor level
Bed seams and baffles
Climb face
Access to the platform
Step stitching and grab line
Tower
Carries the roof and dragon head
Corner seams and roof joint
Slide
Single-lane descent
Entry lip and exit edging
03
Manufacturing Capability
Production runs from a 12,000 m² workshop inside a 70-acre site. Automated cutters lay out the panels, printers apply the artwork, welders join the baffles, and 100-plus heavy sewing machines close the seams. Over 170 employees keep the line at roughly 1,000 inflatables a month.
The tower and slide panels are cut as separate sets and matched by batch number, so a replacement section from a later run still lines up with the print on the first shell.
04
Certification and Testing
Each order of Standard Dragon Multiplay Bounce Castle can ship with an EN 14960-1:2019 compliance file, an SCT product certificate and an RPII inspector report. The management system is audited to ISO 9001, ISO 14001 and ISO 45001.
The 17 oz outer and 9 oz lining are tested to NFPA 701 method 2 and screened for the eight restricted phthalates. Load points on the slide entry and platform edge are the areas the inspector checks first, and the stitched samples are kept for the file.
05
Container Loading
The packed case is 135 x 95 x 78 cm at 167 kg. The tower section is folded on top of the roll so the roof seam is not compressed, and the slide is rolled separately with the print face inward.
Loading plans are quoted from the actual case size, and a photo of the loaded container is taken before the doors close. Consolidated orders are grouped by case size rather than by product line.
06
Hall Requirements
The unit needs 5.2 x 5.5 m plus working space at the entry and the slide exit. Indoors, measure to the lowest beam or light fitting: the 4.9 m roofline is the figure that decides whether a hall takes it.
Grass sites take stakes at every base loop; paving and indoor floors take sandbags or water ballast. The tower presents a tall face to the wind, so the unit is deflated when gusts pick up.
Get A Quote Now — send the theme, the voltage and the site type, and we reply with the drawing and quotation.
07
Dragon Hall and Slide Questions
Q: Which certificates come with this unit?
A: EN 14960-1:2019, SCT product certificate, RPII inspector report, and the ISO 9001, 14001 and 45001 certificates.
Q: Can the slide be replaced on its own?
A: Yes. The slide is a separate chamber joined at a reinforced seam, and a replacement section is quoted against the serial number.
Q: What ceiling height does the unit need indoors?
A: The roofline is 4.9 m, and the blower tube adds to that figure. Measure to the lowest beam, light rig or sprinkler head rather than to the ceiling boards.
Q: How long does a custom theme take?
A: 45 to 60 days from approved artwork. A standard dragon print leaves in about 30 days.
Q: What is the packed weight of the Standard Dragon Multiplay Bounce Castle?
A: 167 kg in a case of 135 x 95 x 78 cm, which needs two or three people or a tail lift.
Send us your detailed inquiry about Inflatable Bouncy Castles,Inflatable Sports Games,Inflatables Accessories, wholesale orders, customized projects or OEM requirements. Our professional team will reply with quotation and solution quickly.
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy