A 14.0 x 7.9 x 2.7 m Inflatable Human Foosball Game with fixed crossbars, a netted goal at each end and a 1.5 HP blower. The shell weighs 204 kg and packs into a 125 x 102 x 95 cm case. Bars run on nylon bearing rings, the shell is 17 oz PVC flame retardant to NFPA 701-2, and the case holds the bar set, ball set and stakes.
Inflatable Human Foosball Game from Leisure Activities®, a China manufacturer, turns table football into a full-size court. Players stand outside the shell and hold a crossbar, so the ball moves in straight lines and the play area stays clear. Fixed bars run across the 7.9 m width; each side holds a goalkeeper bar near its goal and an outfield bar in front of it. The 14.0 m length gives both lines room to move.
01
Features
The court is a constant-air shell with fixed crossbars, a netted goal pocket at each end wall and corner entry gates. Players hold the bars from outside, which keeps the floor clear and makes the game readable from the touchline.
The 2.7 m wall height contains the ball without closing the court off, and the low goal mouth means a shot along the ground scores while a high ball stays in play.
Item
Specification
Inflated size (L x W x H)
14.0 x 7.9 x 2.7 m / 46 x 26 x 9 ft
Unit weight
204 kg / 450 lb
Packed size
125 x 102 x 95 cm / 49 x 40 x 37 in
Outer material
17 oz PVC tarpaulin, NFPA 701-2
Internal material
9 oz PVC, 8P phthalate-free
Crossbars
Fixed aluminium bars, sleeved
Bearings
Nylon rings at each wall sleeve
Goals
Netted pockets at both end walls
Blower
1.5 HP constant air, voltage to order
Anchor points
Webbing loops along both sides
Assembly crew
Two people, about 20 minutes
Packed with
Blower, ball set, bar set, stakes, repair kit
Optional
Spare bar, extra sleeve set, printed rules board
MOQ / lead time
1 piece / 30 days standard
Warranty
1 year limited on seams, blower 1 year
02
Court Design
On the Inflatable Human Foosball Game each bar is an aluminium tube running through stitched sleeves on the wall panel, with a nylon bearing ring at the wall and a capped end. The sleeve is double stitched and bar-tacked at the joint, which is the point that takes the push and pull of play.
A bar slides out of its sleeve for replacement, and the bearing ring and cap are separate parts. The table below describes the two bar positions on each side without a fixed player count, because a hire operator can run smaller teams on the same court.
Bar
Position
Function
Goalkeeper bar
Nearest the goal
Blocks shots on the goal line
Outfield bar
In front of the goalkeeper bar
Passes and shoots
Entry gate
Corner
Substitution without crossing play
03
Game Rules
The game uses a standard football, and a ball set is supplied with the unit. A printed rules board fits on the wall beside the entry, so a new group starts without a briefing.
Three rules cover most play: hold the bar with both hands, no reaching over the wall, and no pushing a bar into another player's line. The board carries those three plus the goal count.
04
Installation
Two people inflate and anchor the court in about 20 minutes. The blower connects at one end, and the tube run is kept off the playing surface.
On grass every base loop along both sides takes a stake. On tarmac or indoors, use water ballast or sandbags. The wall presents a large face to the wind, so the court is deflated when gusts pick up.
05
Customization
Print of Inflatable Human Foosball Game covers the side walls and the goal end panels. A club crest goes on the side wall at eye level, and a sponsor mark goes on the goal end, which is the face that appears in most photographs.
Printing starts only after a physical proof is checked in daylight. Licensed crests need written permission with the file, and the print file is kept for repeat orders.
06
Packaging
At 204 kg the case needs a van with a tail lift or three people. Bars are bundled separately, and the shell folds into a PVC bag with two straps.
The packed case is 125 x 102 x 95 cm. Spares worth holding are a bar, a set of sleeves, a ball set and a blower tube.
Get A Quote Now — send the court size, the voltage and the print direction, and we reply with the quotation and packing plan.
07
Setup and Bar Questions
Q: How long does a spare bar take?
A: A stock bar ships in about 10 days; a bar with printed sleeves takes 30 days from artwork approval.
Q: What voltage does the blower need?
A: Order 220-240 V / 50 Hz or 110 V / 60 Hz; the plug is matched to the market.
Q: Can the court be used indoors?
A: Yes, in a hall that clears the 2.7 m shell plus the blower tube. The cable run is taped down and the goal ends stay clear of walls.
Q: Can the print on the Inflatable Human Foosball Game be changed after the first season?
A: Yes. A new panel set is printed from a fresh proof, and the shell is reused if the sleeves and walls are sound.
Q: What does the warranty cover?
A: Seams and workmanship are covered for a year, and the blower for the same period. Bar wear and net damage are excluded.
Send us your detailed inquiry about Inflatable Bouncy Castles,Inflatable Sports Games,Inflatables Accessories, wholesale orders, customized projects or OEM requirements. Our professional team will reply with quotation and solution quickly.
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy