Products
PK Shootout Inflatable Soccer Game
  • PK Shootout Inflatable Soccer GamePK Shootout Inflatable Soccer Game
  • PK Shootout Inflatable Soccer GamePK Shootout Inflatable Soccer Game
  • PK Shootout Inflatable Soccer GamePK Shootout Inflatable Soccer Game

PK Shootout Inflatable Soccer Game

Leisure Activities® offers the PK Shootout Inflatable Soccer Game for commercial purchase, featuring a three-hole shooting target with individual rear net pockets for interactive football challenges. Measuring 5.8 × 4.0 × 4.3 m, this constant-air inflatable uses 17 oz PVC tarpaulin and a 1.5 HP blower. Its replaceable printed target face and customizable sponsor graphics make it suitable for football clubs, fan zones, school events, sports promotions, and brand activations.

PK Shootout Inflatable Soccer Game from Leisure Activities®, a China manufacturer, is built around a single printed target face. Three cut-outs sit in that face, each with a net pocket behind it, and the whole face is replaced as one set when a target wears through. Players shoot from a marked line and reset from a ball bin behind it.

PK Shootout Inflatable Soccer Game
01

Features

The unit is a constant-air shell with a goal face, two side walls and a low containment wall behind the target. The 4.3 m height gives the face enough surface for three cut-outs without making the shell hard to handle.

A 1.5 HP blower holds the shell at pressure. The target face, side walls and goal pocket are all part of the same shell, so the game stands as one piece rather than a set of separate boards.

Item Specification
Inflated size (L x W x H) 5.8 x 4.0 x 4.3 m / 19 x 13 x 14 ft
Unit weight 143 kg / 315 lb
Packed size 144 x 97 x 76 cm / 57 x 38 x 30 in
Outer material 17 oz Plato PVC tarpaulin, NFPA 701-2
Internal material 9 oz PVC, 8P phthalate-free
Target face One printed panel, three cut-outs
Net pockets Stitched behind each cut-out
Blower 1.5 HP constant air, voltage to order
Anchor points Webbing loops on the base skirt
Assembly crew Two people, about 20 minutes
Packed with Blower, ball set, pump, stakes, repair kit
Optional Spare target set, extra ball set, sponsor panel
MOQ / lead time 1 piece / 30 days standard
Warranty 1 year limited on seams, blower 1 year
02

Target Design

On the PK Shootout Inflatable Soccer Game the face is printed PVC with three cut-outs, and each pocket is stitched to the back of the panel around its opening. Face and pockets are one assembly, so they are replaced together rather than one at a time.

A replacement set is printed from the stored file, so a second season matches the first without a new proof. The set is quoted against the serial number on the data plate.

PK Shootout Inflatable Soccer Game
03

Applications

The game suits fan zones, club family days, school fetes and sponsor activations where a queue has to keep moving without a referee. The shooting line can be marked on grass, paving or a hall floor.

The unit packs into a van with two people, so a club can take it to an away fixture or a sponsor event without a trailer.

Site check Requirement
Ground Level, free of stones and glass
Surface Grass, paving, decking or mat
Overhead Clear of cables and branches
Anchors Every base loop used
Blower Behind the unit, cable covered
04

Installation

The unit occupies 5.8 x 4.0 m, and the working area is closer to 8 x 6 m once the shooting line and the queue are marked. Keep the queue to one side rather than in front of the goal, and leave space behind the unit for the blower and the ball bin.

Grass takes the stakes supplied; paving, decking and indoor floors take water ballast or sandbags on the same loops. The goal face presents a large surface to the wind, so the unit comes down when gusts pick up.

PK Shootout Inflatable Soccer Game
05

Customization

Print covers the target face and the side walls. A club crest goes on the side wall, and a sponsor mark goes on the target face, which is the panel photographed most often.

Production begins once the printed proof has been checked in daylight. Licensed crests need written permission with the file.

06

Packing & Spare Parts

At 143 kg the case needs two people or a tail lift. The target set is wrapped and packed with the shell, and the balls and pump travel in the accessory bag.

Spares worth holding are a target set, a goal net, a ball set and a blower tube.

Get A Quote Now — send the target layout, the voltage and the sponsor artwork, and we reply with the quotation and proof schedule.

PackingPackingPackingPacking

07

Target and Scoring Questions

Q: Can the sponsor panel on the PK Shootout Inflatable Soccer Game be changed without replacing the target face?

A: Yes. The side-wall sponsor panel is printed separately from the target face, so it can change while the face stays in service.

Q: Can the game be used indoors?

A: Yes, with the ceiling clear above the shell and the cable run taped down. The shooting line is marked on the floor.

Q: Which voltage does the blower use?

A: Two voltages: 220-240 V / 50 Hz and 110 V / 60 Hz, with the plug per destination.

Q: How long does a spare target set take?

A: About 10 days for a stock set, and 30 days for a printed set matched to the serial number.

Q: What is covered by the warranty?

A: Twelve months on seams and workmanship, twelve months on the blower. Target print wear and lost balls are excluded.

Send Inquiry
Contact Info
Send us your detailed inquiry about Inflatable Bouncy Castles,Inflatable Sports Games,Inflatables Accessories, wholesale orders, customized projects or OEM requirements. Our professional team will reply with quotation and solution quickly.
X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
RejectAccept